per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
3
11
824
Article
مدلسازی عددی شکست هیدرولیکی در مخازن نفتی با اجزاء محدود توسعهیافته
NUMERICAL MODELING OF HYDRAULIC FRACTURING IN OIL RESERVOIRS WITH EXTENDED FINITE ELEMENT METHOD
مصطفی ملاعلی
m.molaali@gmail.com\\
1
محمود یزدانی
myazdani@modares.ac.ir
2
دانشکدهی مهندسی عمران و محیطزیست، دانشگاه تربیت مدرس
دانشکدهی مهندسی عمران و محیطزیست، دانشگاه تربیت مدرس
از جمله روشهای استخراج نفت و گاز، شکست هیدرولیکی است که طی آن، سیالی با فشاری بیشتر از تنش برجای منطقه به محلی از چاه که توسط پکرها ایزوله شده است، تزریق میشود و در نهایت، زمانی که فشار سیال از تنش برجای حاکم بر منطقه فراتر رود، شکست هیدرولیکی رخ خواهد داد. یکی از جدیدترین روشهای عددی جهت مدلسازی شکست هیدرولیکی روش اجزاء محدود توسعهیافته است. در این روش، با توجه به اصل تفکیک پیوستگی در اثر اعمال توابعی ویژه، گرههای اطراف ترک غنی میشوند و در نتیجه درجات آزادی گرهها افزایش مییابند و به واسطهی همین درجات آزادی، بیشتر امکان تغییر در جابجاییهای گرهیی اطراف ترک فراهم میآید. در این پژوهش، برای انجام مدلسازی، یک برنامهی رایانهیی به روش اجزاء محدود توسعهیافته نوشته شده است. برای صحتسنجی برنامهی رایانهیی، نتایج آن با یک حل تحلیلی دوبعدی مقایسه شده و درستی آن به تأیید رسیده است.
Due to more than one hundred years of oil and gas extraction, most reservoirs, especially those with high ermeability, are gradually running out. Hence, the tendency is towards utilization of reservoirs with low permeability. Also, after continuous extraction of hydrocarbon products, natural reservoir pressure is reduced, cracks are losed nd he roduction of the reservoir is reduced. It is, therefore, necessary to undertake additional methods in order to enhance the capacity of such reservoirs; hydraulic fracturing is such a method, which is popularly applied to 50\% of oil and 70\% of gas wells in North America.In hydraulic fracturing, the fluid with pressure more than the in-situ stress of the region is injected into the place of the well that had been isolated by packers. When the fluid pressure exceeds the in-situ stress, hydraulic fracturing will occur. One numerical method recently developed for simulation of hydraulic fracturing is the extended finite element method (XFEM). In this method, the nodes surrounding the cracks are enriched through special functions. Accordingly, for such nodes, the degrees of freedom are increased, which results in greater displacement around each crack. In this research, a XFEM code was developed to simulate the hydraulic fracturing problem.The code provides three interaction processes: (I) Mechanical deformation due to fluid pressure on the crack, (II) Fluid flow in the crack and (III) Crack propagation due to fluid motion. The results of numerical analysis by the provided code, which is examined on a classic hydraulic fracturing \ problem, exhibit \ decreasing \ fluid pressure and \ increasing \ crack openings at the borehole well, as the crack length progresses. These results are in line with the results obtained by the KGD analytical solution. Also, it was observed that the width of the crack opening should be increased to enhance the exploitation of hydrocarbon products. In order to reach this goal, the fluid viscosity and/or injection rate of the fluid should be increased.
https://sjce.journals.sharif.edu/article_824_ea08a5e55e6b7945ea190c95240480fe.pdf
شکست هیدرولیکی
مخازن نفتی
اجزاء محدود توسعهیافته
Hydraulic fracturing
oil reservoirs
extended finite element method
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
13
24
831
Article
تجزیه و تحلیل پارامتریک سد انحرافی با استفاده از الگوریتم ژنتیک
BARRAGE PARAMETRIC ANALYSIS USING GENETIC ALGORITHM
سعید میرزائی فیلستان
s.mirzaei88@ms.tabrizu.ac.ir
1
فرزین سلماسی
salmasi@tabrizu.ac.ir
2
داود فرسادی زاده
farsadi@tabrizu.ac.ir
3
هادی اورنقی
arvanaghi@tabrizu.ac.ir
4
دانشکدهی مهندسی کشاورزی، دانشگاه تبریز
دانشکدهی مهندسی کشاورزی، دانشگاه تبریز
دانشکدهی مهندسی کشاورزی، دانشگاه تبریز
دانشکدهی مهندسی کشاورزی، دانشگاه تبریز
هزینهی احداث سدهای انحرافی برای انواع مختلف خاکها و در شرایط مختلف هیدرولوژیکی متغیر است، که نیاز به طراحی دقیق و تحلیلهای هیدرولیکی، هیدرولوژیکی و سازهیی دارد. در این نوشتار، یک مدل بهینهسازی برای تعیین پارامترهای اساسی سد انحرافی از جمله عمق دیوارهای سپری، طول و ضخامت کف براساس تئوری خوسلا برای جریان زیرسطحی ارائه شده است و با توجه به غیرخطی و چندمتغیرهبودن تابع هدف و غیرخطیبودن قید مسئله، تجزیه و تحلیل پارامتریک با استفاده از الگوریتم ژنتیک با نرمافزار Matlab صورت گرفته است. نتایج نشان میدهند که احداث سد انحرافی بر روی خاکهای ماسهیی کم هزینهتر از احداث سد انحرافی بر روی خاکهای سیلتی یا سیلتی رسی است و همچنین عمق دیوار سپری بالادست نسبت به عمق دیوار سپری پاییندست و طول کف، حساسیت بسیار پایینتری در مقابل تغییرات مقدار گرادیان هیدرولیکی خروجی مجاز و هد آب دارد.
The, so called, barrage diverts water from rivers and steers it to the main channel. This requires careful design and analysis of hydraulic, hydrological and structural engineering. Barrage construction cost is not constant and, for a variety of different soil and hydrological conditions, the cost varies. The depth of sheet-piles/cutoffs and the length and thickness of the floor are the parameters influencing the cost of barrages. When a sheet-pile depth is changed, floor length and uplift force change over the floor, which has an impact on floor thickness and makes the cost of the barrage change to a non-linear form. In the present study, an optimization model is presented to fix the basic barrage parameters, which are depth of sheet piles/cutoffs, and length, and the thickness of the floor is based on Khoslas theory for subsurface flow. Basic barrage parameters need to be optimized, so that barrage costs for filling, xcavation, dewatering, concreting, sheet-piling and driving will be minimal, provided that the output of the hydraulic gradient does not exceed the permissible hydraulic gradient. Therefore, note that the objective function is nonlinear and the multivariate and nonlinear constraint of the problem is optimized using the genetic algorithm. The lgorithm, udiciously searches for optimal design within the problem space. Matlab software is a complete toolbox in the field of genetic algorithms, therefore, all procedures relating to the genetic algorithm is performed in Matlab software. Results of parametric analysis using the genetic algorithm show that a barrage founded on sand would cost less than a barrage on silt or silty clay for the same head, and the depth of the upstream sheet pile is sensitive neither to the value of permissible exit gradient nor to the seepage head.
https://sjce.journals.sharif.edu/article_831_ac44fd2192ca957b54458dbf3390e8db.pdf
سد انحرافی
گرادیان هیدرولیکی خروجی
دیوار سپری
تئوری خوسلا
الگوریتم ژنتیک
Matlab
Barrage
hydraulic exit gradient
sheet-pile
Khosla's theory
Genetic algorithms
Matlab
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
25
34
825
Article
تأثیر سختی کلاهک در رفتار گروه شمع تحت اثر بار زلزله
EFFECT OF PILE CAP STIFFNESS ON THE BEHAVIOR OF PILE GROUP UNDER EARTHQUAKE LOADING
محمد علیایی
m.olyaei@modares.ac.ir
1
کمیل خاکپور
k_khakpour@modares.ac.ir
2
دانشکدهی مهندسی عمران و محیط زیست، دانشگاه تربیت مدرس
دانشکده مهندسی عمران و محیط زیست - دانشگاه تربیت مدرس
پیهای شمعی اغلب بهصورت گروه شمع برای سکوهای دریایی، پلها و ساختمانهای بلند استفاده میشوند. هدف این پژوهش، بررسی اثر سختی کلاهک گروه شمع در رفتار شمعها تحت اثر بار دینامیکی با استفاده از روش تفاضل محدود سهبعدی در خاکهای ماسهیی است. تحقیقات نشان میدهد که سختی کلاهک گروه شمع، شرایط اتصال شمع به کلاهک و اندرکنش سازه ـ شمع ـ خاک تأثیر قابل ملاحظهیی در رفتار گروه شمع در برابر بارهای جانبی دارد. در این نوشتار، برای اتصال شمعها به یکدیگر از المان تیر استفاده شده است. مطالعهی سختی کلاهک شمع نشان میدهد با افزایش یا کاهش سختی کلاهک شمع، بیشینهی جابهجایی، بیشینهی نیروی برشی و بیشینهی لنگر خمشی در شمعها الزاماً کاهش یا افزایش نمییابد، بلکه با توجه به جرم مجموعه، برای هر گروه شمع محدودهیی از سختی کلاهک وجود دارد، که در آن بیشترین جابهجایی، نیروی برشی و ممان در شمعها ایجاد میشود.
Piles are often placed closely in a group to serve as the foundation of specific structure, such as offshore platforms, bridge structures and tall buildings. Pile groups should be capable of withstanding significant lateral loads induced by seismic excitations, winds, waves, and current loads. The main objective of this research is to investigate the effect of the stiffness of the pile cap on the behavior of piles embedded in sand under dynamic loads, by means of the 3D finite difference method. Previous research shows that pile cap stiffness, connection type of pile-cap and soil-pile-structure interaction play important roles in the behavior of laterally loaded pile groups. Beam elements are used in this study to connect each of the piles, and these connections are rigid. Further, due to he nfluence f he uperstructure on the behavior of pile foundations, this effect is modeled in the analyses. To account for the soil stiffness acting on the pile shaft, normal and shear springs are accommodated in the interface of the soil and pile elements. To evaluate the data for the parameters of the interface elements, a 2D finite difference analysis has been performed to calculate the required parameters of the interface elements at various depths. To model sand and structural members, Mohr-Coulomb and elastic models are employed, respectively. For dynamic analyses, attention has been paid to quiet boundaries, free fields, and wave propagation in the soil medium. Four different arrangements have been considered for pile cap. Results of analyses show that a increase or decrease in cap stiffness does not necessarily change extreme induced forces (i.e., maximum shear force, bending moment and lateral displacement) along the piles in the group. However, for a given mass of the system, there is a range of stiffness for the pile group that has maximum effect on induced internal forces and lateral displacements. For a flexible pile cap, the induced bending moments and shear forces along the individual piles depend on the location of the piles in the group.
https://sjce.journals.sharif.edu/article_825_c5e921877d829195bc2d25bce25b846c.pdf
سختی کلاهک گروه شمع
تحلیل دینامیکی
اندرکنش سازه ـ شمع ـ خاک
تحلیل تفاضل محدود سهبعدی
Pile cap stiffness
Dynamic analysis
soil-pile-structure interaction
3D finite difference analysis
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
35
44
832
Article
بررسی خواص مکانیکی مصالح ماسهیی در فصل مشترک با بتن آسفالتی
AN INVESTIGATION INTO THE MECHANICAL PROPERTIES OF GRANULAR MATERIALS IN AN INTERFACE WITH ASPHALTIC CONCRETE
رضا مهین روستا
r_mahinroosta@yahoo.com
1
حسن طاهرخانی
taherkhani.hasan@znu.ac.ir
2
میلاد تاج الدینی
milad\_tajdini@ alum.sharif.edu
3
دانشکدهی مهندسی عمران و محیط زیست، دانشگاه تربیت مدرس}
دانشکدهی فنی و مهندسی، دانشگاه زنجان
دانشکدهی فنی و مهندسی، دانشگاه زنجان
هستههای بتن آسفالتی برای اولین بار در سال ۱۹۴۸ بهعنوان المان آببند در سدهای سنگریزهیی مورد استفاده قرار گرفتند. استفاده از اینگونه هستهها در مناطق سردسیر و پر باران و لرزهخیز نسبت به هستهی رسی توصیه شده است. به دلیل مجاورت مصالح بتن آسفالتی هسته و مصالح ماسهیی اطراف، رفتار در سطح مشترک این دو ماده پیچیده میشود و برای رفع این ابهام، نیاز به بررسیهای آزمایشگاهی بر روی سطح تماس آنها احساس میشود. بر این اساس، در این نوشتار آزمایشهایی با دستگاه برش مستقیم کوچکمقیاس cm) ($10\times10\times2.5$، که سطح برشی آن بهعنوان سطح تماس در نظر گرفته شد، انجام شده است. نتایج آزمایشها کاهش پارامترهای مکانیکی در مصالح سطح تماس نسبت به مصالح ماسهیی را نشان داد. همچنین نسبت اندرکنش تعیین شد که در محدودهیی مشخص قرار داشت.
Asphaltic concrete has been used as a waterproofing core for embankment dams since 1948. Worldwide, the large majority of the embankment dam central core is made of clay. However, as clay is increasingly difficult to find at new construction sites, asphalt concrete has been used as a replacement core material. Core made of clay has some further disadvantages, such as; low shear strength, compressibility, long construction time, requiring higher amounts of material, and accurate controls during construction, etc. The advantages of using asphalt concrete are; less sensitivity to weather conditions, less width of core, the healing behavior of bitumen and high shear strength etc. In this application, granular materials are used around the asphaltic concrete as a filter, which creates complicated behavior at the interface and which needs to be researched by experiment and modeling. This paper describes the experimental work and the results of investigating the mechanical behavior of the interface between aggregates and asphaltic concrete. A small scale shear strength test has been used in this study, in which the hear urface s onsidered as the interface. The effect of bitumen penetration grade, moisture, density and angularity of aggregates on the shear strength parameters at different levels of vertical stresses and constant shear rate was studied. Asphalt concrete specimens were cut in square shapes (10ش10ش2.5cm) from cylindrical specimen compacted by a modified marshal compaction method. The results show that the shear strength parameters increase with increasing the density and vertical stress level. It is also shown that the shear parameters decrease with increasing moisture content in the interface. The penetration grade of bitumen does not have a significant effect on the parameters. It is also demonstrated that the ratio of interaction between the aggregate and asphalt concrete decreases in a certain range of variation.
https://sjce.journals.sharif.edu/article_832_dec7a5c5283ba57e9dc46486b4661769.pdf
بتن آسفالتی
مصالح ماسهیی
مصالح سطح تماس
اندرکنش
آزمایش برش مستقیم کوچکمقیاس
asphalt concrete
sand material
interface
interaction
small scale direct shear test
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
45
55
833
Article
بررسی آزمایشگاهی رفتار چرخهیی اتصالات بتنآرمهی مقاومسازیشده با دستک فلزی
EXPERIMENTAL INVESTIGATION OF THE CYCLIC BEHAVIOUR OF RC CONNECTIONS STRENGTHENED WITH STEEL PROP AND CURB
ابراهیم امامی
emami@se.pnu.ac.ir
1
محمدکاظم شربتدار
msharbatdar@semnan.ac.ir
2
علی خیرالدین
kheyroddin@semnan.ac.ir
3
گروه مهندسی عمران، دانشگاه پیام نور، تهران
دانشکدهی مهندسی عمران، دانشگاه سمنان
دانشکدهی مهندسی عمران، دانشگاه سمنان
این نوشتار به بررسی آزمایشگاهی رفتار چرخهیی سه اتصال بتنآرمهی خارجی کناری با بتن کم مقاومت و با مقیاس $\frac{1}{2}$ ، شامل دو اتصال مرجع مقاومسازینشده با ارتفاع متفاوت تیر، اولی با ارتفاع کم و دومی با ارتفاع استاندارد و اتصال سوم مشابه نمونهی مرجع اولی، که با سیستم پیشنهادی دستک و طوقهی فلزی یکطرفه مقاومسازی شده است، میپردازد. نتایج و مشاهدات آزمایشگاهی نشان دادند که کاهش ۲۵\٪ ارتفاع تیر اتصال بتنی، موجب کاهش سختی و افزایش جابجایی نوک تیر اتصال، کاهش شکلپذیری، ظرفیت باربری و جذب انرژی آن شدند. همچنین سیستم مقاومسازی پیشنهادی با افزایش قابل توجه مقاومت و کاهش افت سختی اتصال و با بالابردن جذب انرژی اتصال با تیر ضعیف، میتواند میزان خسارتهای ناشی از بارهای جانبی رفت و برگشتی در ناحیهی اتصال تیرـ ستون و چشمهی اتصال را به میزان کمینه برساند.
At several last decades, the researchers have suggested various methods for strengthening of reinforced concrete beam- column connections that each of them has deficiencies and advantages. Each proposed method has particular advantages such as increasing capacity, stiffness, material costs, construction process cost and professional labor, so due to new required property of deficient structure, one of those method can be applied. This \ paper \ presents \ an \ experimental \ investigation of \ strengthening effects on the external corner weak (with low \ strength concrete and \ low height \ of beam ) reinforced \ concrete (RC) beam-column connections by suggestion method of steel elements (steel prop \& curb) subject to cyclic loading. Three half scale RC beam-column connections with low strength concrete were prepared and casted, including of two un-strengthened reference connections with different height of beam (low and standard height), and another with low height of beam that was strengthened by suggested system of one direction steel prop and curb that then every sample were subjected to cyclic loading. The experimental results and observations indicated that by 25\% reduction of height of connection beam, caused to reduction in stiffness, increasing the lateral displacement of beam of connection and also reduction 25\%, 33\% and 26\% in ductility, bear capacity and energy absorption respectively. Also, it was determined that the suggested system of strengthening, by increasing strength and decreasing stiffness degradation, and raising the nergy bsorption of RC weak beam- column connection, can minimize the damages due to cyclic loading in the beam to column joint and panel zone. It can cause to development behavior of weak RC connection, as the performance of weak RC connection was upgraded to limit of behavior of connection with standard beam. Therefore, this suggested system with any different sizes and angles, corresponding to the required strength and stiffness can be easily applicable for any deficient RC beam-column connection in RC frames.
https://sjce.journals.sharif.edu/article_833_9941b103c00e2731b37966451c555ff5.pdf
اتصال تیر ـ ستون
مقاومسازی
دستک فلزی
طوقهی فلزی
قاب بتنآرمه
Beam-column connection
Strengthening
steel prop
steel curb
RC frame
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
57
65
836
Article
مقایسهی قابلیت دو اکسیدکنندهی NaIO$_4$ و NaBrO$_3$ بر بهبود فرایند فتوکاتالیستی UV/TiO$_2$ در حذف رنگزای آبی مستقیم ۷۱
COMPARING THE CAPABILITY OF $bf{NAIO_4}$ AND $bf{NABRO_3}$ OXIDANTS ON IMPROVING $bf{UV/TIO_2}$ PHOTOCA-TALYTIC PROCESS IN REMOVAL OF DIRECT BLUE 71 DYE
بیتا آیتی
ayati_bi@modares.ac.ir
1
معصومه پنبه کار بیشه
m.panbehkarbisheh@modares.ac.ir
2
دانشکده مهندسی عمران و محیط زیست - دانشگاه تربیت مدرس
دانشکده مهندسی عمران و محیط زیست -دانشگاه تربیت مدرس
هدف اصلی از انجام این مطالعه، بررسی اثر افزودن دو اکسیدکنندهی NaIO$_4$ و NaBrO$_3$ در فرایند فتوکاتالیستی با استفاده از نانو ذرات TiO$_2$ تثبیتشده بر بستر بتن به کمک اشعهی UV جهت حذف رنگزای آبی مستقیم ۷۱ بوده است. پارامترهای غلظت اولیهی رنگزا، pH، شدت تابش UV-C و دز اکسیدکننده در طی انجام آزمایش جهت تعیین شرایط بهینه مورد بررسی قرار گرفته است. در شرایط غلظت اولیهی ppm ۲۰۰، مقدار gr/m$^2$ ۴۰ ذرات TiO$_2$، لامپ ۹۰ وات و مقدار gr/L ۰٫۰۶۴ اکسیدکنندهی NaIO$_4$ در مدت زمان ۲۵ دقیقه برای سیستمهای UV/TiO$_2$، UV/NaIO$_4$ و V/TiO$_2$/NaIO$_4$ به ترتیب برابر ۳۹٫۴، ۷۹٫۵۴ و ۸۴٫۷۵ درصد و همچنین با غلظت اولیهی ppm ۱۰۰، gr/L ۰٫۰۴۵ اکسیدکنندهی NaBrO$_3$ و حفظ دیگر شرایط در سیستمهای UV/NaBrO$_3$ و UV/TiO$_2$/NaBrO$_3$ به ترتیب ۶۲٫۹۱ و ۶۶٫۱۹ درصد راندمان حذف مشاهده شد، که بیانگر قویبودن اکسیدکنندهی NaIO$_4$ نسبت به NaBrO$_3$ است.
Synthetic dyes are widely used in many industries, such as, textile dyeing, leather tanning, plastic and paper. In general, more than 40 percent of initial dye mass remains in the dye bath, which means that it is highly contaminated. Azo dyes, the largest class of synthetic dyes, are distinguished by containing one or more azo groups (-N=N-) that are bounded to the aromatic rings. They not only give color to water but also have mutagenesis and carcinogenesis potential and induce the production of toxic byproducts. They are difficult to remove from wastewater using common physical, chemical and biological treatment methods, and, therefore, it is essential to look for appropriate techniques for treatment of these kinds of pollutant to reduce their environmental impact. Recently, application of advanced oxidation methods, such as photo catalytic reactions, for removing toxic and non-bio-degradable pollutants from drinking water and textile wastewater have been expanded. It is based on the generation of hydroxyl radicals (0OH) with great oxidizing potential that can quickly and non-selectively oxidize a wide spectrum of diverse organic dyes. This method does not have the problem of residuals and, also, can be used at room temperature and under atmospheric pressure. The main objective of this study is to examine the effect of adding oxidants, $NaIO_4$ and $NaBrO_3$, in a photocatalytic process using $TiO_2$ nanoparticles immobilized on concrete substrate using UV radiation in different systems for the removal of direct blue 71 dyes. In order to determine the optimum conditions, initial dye concentration, pH, intensity of UV-C radiation, and oxidants dosage during testing, were investigated. After 25 minutes, 39.4, 79.54 and 84.75 percent removal efficiency was obtained for three systems of $UV/TiO_2$,$UV/NaIO_4$ and UV/$TiO_2$/$NaIO_4$, in initial dye concentrations of 200 ppm, $40 gr/m^2$ of nano $TiO_2$, light intensity of 90 watts and 0.064 gr/L $NaIO_4$, respectively. At the same time, 62.91 and 66.19 percent removal efficiency was observed for $UV/TiO_2/NaBrO_3$ and $UV/NaBrO_3$ or initial dye concentrations of 100ppm and 0.045 gr/L $NaBrO_3$. This means that $NaIO_4$ is a stronger oxidant in comparison to $NaBrO_3$.
https://sjce.journals.sharif.edu/article_836_4e2cb931bd4c6602a3553e12d450c0c4.pdf
شدت تابش
غلظت
رنگزای آبی مستقیم ۷۱
pH
Light intensity
concentration
dye direct blue 71
pH
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
67
74
826
Article
بررسی تأثیر میراگرهای الحاقی در پاسخ دینامیکی سازههای جداسازیشدهی لرزهیی تحت اثر زلزلههای حوزهی نزدیک و دور
EFFECT OF SUPPLEMENTAL DAMPING ON SEISMIC RESPONSE OF ISOLATED STRUCTURES UNDER NEAR \& FAR FIELD EARTHQUAKES
مجتبی فتحی
fathim@razi.ac.ir
1
اکبر مخدومی
makhdoumi.ar@gmail.com
2
دانشکده فنی مهندسی - دانشگاه رازی کرمانشاه
دانشکده فنی مهندسی - دانشگاه رازی کرمانشاه
جداسازی لرزهیی بهمنزلهی یک رویکرد نوین کنترل غیرفعال سازه قادر است بهطور چشمگیری پاسخ سازه را در حرکات قوی زمین کاهش دهد. عملکرد این سیستمها در زلزلههای حوزهی نزدیک، که حاوی شتابهایی با محتوای بسامدی بالا و پالسهای بلند هستند، با تردید روبرو است. بهکارگیری میراگرهای ویسکوز در تراز جداسازی، یکی از راهکارهای ارائهشده برای بهبود عملکرد این سیستمها در زلزلههای حوزهی نزدیک است. در این نوشتار، تأثیر مقادیر مختلف میرایی الحاقی از ۵\٪ تا ۴۰\٪ در سازههای جداسازیشده تحت زلزلههای مختلف در نرمافزار ABAQUS مورد بررسی قرار گرفته است. نتایج نشان داده است که افزایش میرایی الحاقی در شتابنگاشتهای حوزهی نزدیک، جابجایی تراز جداسازی را کاهش میدهد، اما سبب افزایش جابجایی نسبی طبقات و شتاب طبقات میشود. در حالی که افزایش میرایی الحاقی در تحلیلهای تحت شتابنگاشتهای حوزهی دور سبب کاهش جابجایی تراز جداسازی، جابجایی نسبی طبقات، و افزایش شتاب طبقات میشود.
Seismic isolation as a passive control method of structures and an innovative approach in resistant seismic design reduces significantly the responses of structural system induced by strong ground motions. The performance of these systems in near fault (NF) ground motions with large pulses is different from far fault (FF) ground motions. It is shown that the effects of near field earthquake with large velocity pulses can bring the seismic isolation devices to critical working conditions. To overcome this problem the application of viscous damper is represented as an approach to improve the performance of these systems in near field earthquakes. In the present paper, by modeling six base isolated structures, the seismic responses has been studied under near field and far field earthquakes. The isolators were modeled by using a mathematical model depicted by bi-linear hysteretic behavior. Nonlinear time history analyses were performed using finite element software of ABAQUS to study the influence of different values of supplemental damping (5\%-40\%) on the responses of base isolated structures. The variation of floor absolute acceleration, bearing displacement and storey drift for different values of supplemental damping under near field and far field earthquakes was studied. The influence of supplemental damping on the responses of isolated structures were studied under the variation of important system parameters uch s uperstructure flexibility, period of frames and number of storey of base isolated structures. The results showed that, generally, by increasing the damping ratio, responses of structures including the maximum floor acceleration and maximum floor relative displacements increased under near field earthquakes. But maximum floor elative isplacements decreased under far field earthquakes. It was observed that base displacement response decreased by increasing damping ratio under near field and far field earthquakes. This reduction under near field earthquakes is greater than far field earthquakes. Also by increasing the supplemental damping under near field and far field earthquakes, the maximum story acceleration increased.
https://sjce.journals.sharif.edu/article_826_0cf5d3eff3dc347f142f8482f7cd6114.pdf
میراگر الحاقی
جداسازی لرزهیی
تحلیل دینامیکی غیرخطی
زلزلهی حوزهی نزدیک
seismic isolation
near field
damping
subgrade
ABAQUS
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
75
83
828
Article
مطالعهی آزمایشگاهی رفتار بستر مسلح با ژئوسل لایهیی تحت بارگذاری سیکلی
EXPERIMENTAL STUDY OF LAYERED GEOCELL REINFORCED BED SUBJECTED TO REPEATED LOAD
پیام شریفی
sharifipayam.civil@gmail.com
1
سیدناصر مقدس تفرشی
nas_moghaddas@kntu.ac.ir
2
دانشکده مهندسی عمران، دانشگاه صنعتی خواجه نصیرالدین طوسی
دانشکده مهندسی عمران- دانشگاه صنعتی خواجه نصیرالدین طوسی
در این نوشتار با انجام مطالعات آزمایشگاهی، رفتار بستر مسلح با یک و دو لایهی ژئوسل تحت بارگذاری تکراری نظیر بار ترافیک وسائط نقلیه بررسی شده است. بارگذاری تکراری با اعمال بیش از ۲۰۰۰۰ سیکل تا رسیدن نشست به یک حالت پایدار یا بروز نشستهای مفرط ادامه یافته است. نتایج نشان میدهد که نشست در سیکلهای اول بارگذاری درصد قابل توجهی از نشست نهایی در انتهای بارگذاری را شامل میشود، که این امر مبین اثر سیکلهای اولیه بهعنوان یک ویژگی رفتاری مهم بستر تحت بارگذاری سیکلی است. ضخامت بهینهی خاک بین دو لایهی ژئوسل برای دستیابی به کمینهی نشست حدود ۰٫۲ قطر صفحهی بارگذاری است. همچنین با استفاده از دو لایهی ژئوسل با فاصلهی بهینه از یکدیگر به جای استفاده از یک لایهی ژئوسل )با میزان یکسان از ژئوتکستایل مصرفی در هر دو حالت(، میتوان مقدار نشست در سطح خاک را به میزان قابل توجهی کاهش داد.
This paper describes a series of laboratory tests performed on geocell reinforced soil beds, with one and two layers of geocell and different heights of geocell under repeated loads (loading, unloading and re-loading), to simulate vehicle traffic loads. A soil surface settlement up to 20000 load repetitions was recorded, until its value became stable or failure occurred due to excessive settlement. The influence of the height of geocell layers, H, in terms of H/D (H: the height of geocell layers, and D: the loading surface diameter) and vertical spacing of the two geocell layers, and h, in terms of h/D, in the foundation bed, were studied. Assessment of performance is investigated for one and two layers of geocell, whereas the used mass of geocell material is kept constant. For example, the experiment reinforced by two layers of geocell with H/D=0.225 has exactly the same mass of geocell compared with the experiment reinforced by one thicker layer of geocell reinforcement with H/D=0.45. The results show that the settlement under repeated loads is the large portion of the settlement that occurs during the first few cycles of loading and unloading compared to the total settlement recorded after all cycles. The optimum vertical spacing of geocell layers was found to be approximately 0.2 times the loading plate diameter (i.e., h/D=0.2). For one layer reinforcement, with an increase in the height of the geocell, the settlement of the loading plate decreases. The reinforced bed with two layers of geocell has more efficiency than one layer of geocell in reducing the surface settlement, whereas the same mass of geocell was used in the foundation bed. For example, the maximum settlements of loading plate for the two layers of geocell-reinforced soil bed with H/D=0.225 (h/D= 0.2) and for one layer of geocell-reinforced soil bed with H/D=0.45, at the end of loading, are 36\% and 28\% of the loading plate diameter, respectively.
https://sjce.journals.sharif.edu/article_828_13d9f1ed3fdaae6585038097efee01e8.pdf
بستر مسلح
ژئوسل لایهیی
نشست صفحهی بارگذاری
بارگذاری سیکلی
Geocell-reinforced sand
layered geocell
soil surface settlement
repeated load
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
85
95
829
Article
ارائهی روابط کاهندگی برای بیشینهی شتاب افقی و قائم جنبشهای نیرومند زمین در فلات ایران با استفاده از الگوریتم توسعهی ژنی (GEP)
ATTENUATION RELATIONSHIPS FOR PEAK GROUND ACCELERA-TION IN THE IRANIAN PLATEAU USING GENE EXPRESSION PROGRAMMING (GEP)
غلامرضا قدرتی امیری
ghodrati@iust.ac.ir
1
محمد شامخی امیری
shamekhi@shahroodut.ac.ir
2
دانشکدهی مهندسی عمران، دانشگاه علم و صنعت ایران
دانشکدهی مهندسی عمران، دانشگاه شاهرود
هدف از این نوشتار، ارائهی روابط کاهندگی برای بیشینهی شتاب افقی و عمودی جنبش نیرومند زمین، در فلات ایران با استفاده از الگوریتم توسعهی ژنی )GEP( است. عوامل مؤثر در این پیشبینی بزرگای زلزله، فاصلهی منبع زلزلهساختگاه و نوع زمین\پانویس{ground type} در نظر گرفته شدهاند. ابتدا فلات ایران به دو بخش البرز ـ ایران مرکزی و زاگرس تقسیم و سپس رکوردهای این نواحی با توجه به نوع ساختگاه به ۲ بخش خاک و سنگ تقسیم شدند. نظر به اینکه زلزلههای رخداده و گزارششده در ایران سطحی هستند، بزرگای موج سطحی بهعنوان بزرگا و فاصلهی کانونی بهعنوان فاصلهی منبع زلزله ـ ساختگاه در نظر گرفته شده است. استفاده از الگوریتم توسعهی ژنی برای محاسبهی روابط کاهندگی دارای این مزیت است که از مدل رگرسیون ثابتی استفاده نشده است و مدل بهصورت هوشمند بهدست میآید. نتایج محاسباتی نیز سازگاری میان نتایج پیشبینیشده و مشاهداتی را نشان میدهند، که ضریب تناسب بالایی دارد.
This paper proposes attenuation relationships for peak ground acceleration (PGA) for horizontal and vertical components of earthquakes in the Iranian plateau. So far, many attenuation relationships have been presented based on several parameters. Attenuation relationships were, initially, simple functions of a few variables, but gradually became more and more sophisticated over time as the number and accuracy of records and the use of computer calculations increased. Ground motion during an earthquake depends mainly on source mechanics, magnitude, local geology, surface topography, source to site distance and the dynamic properties of the material propagation. However, in this research, because of lack of information in Iran, only the magnitude of the earthquake, the distance between the earthquake source and the location and the ground type are used as important factors. Surface wave magnitude (Ms) is used in this research, since the occurred and reported earthquakes in Iran are shallow. Furthermore, hypocentral distance is considered as the distance between the earthquake source and the location. The Iranian plateau is divided into two seismic zones: Alborz-central Iran and Zagros. From a ground-type point of view, the records of each region can be subdivided into two parts. Therefore, all records are grouped into four categories: 1) Alborz and central Iran-rock ground type, 2) Alborz and central Iran-soil ground type, 3) Zagros-rock ground type, and 4) Zagros-soil ground type. In this regard, a majority of available catalogs relating to 490 seismic events in Iran have been gathered, out of which, 954 records are used. These include 493 records related to Alborz and central Iran and the rest associated with the Zagros region. These records comprise earthquakes with a surface wave magnitude greater, or equal to, 4, with a hypocentral distance greater than 5 km (and often less than 200 km). To obtain the attenuation relationships for peak ground acceleration, a Gene Expression Programming (GEP) algorithm is used instead of the conventional constant regression model. The model is extracted smartly as a continuous period function. The results show a consistency with a high proportionality coefficient among the observed and anticipated results.
https://sjce.journals.sharif.edu/article_829_0211b47435a94135c2c7ca8b1eab8ae7.pdf
روابط کاهندگی
الگوریتم توسعهی ژنی
بیشینهی شتاب زمین
فلات ایران
سنگ
خاک
Attenuation relationship
GEP
PGA
Iran
rock
soil
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
97
108
830
Article
تأثیر رفتار کاهندهی چرخهی هیسترزیس در تحلیلهای استاتیکی غیرخطی برای قابهای بتنی خمشی ویژه با دیوار برشی
INVESTIGATION OF DETERIORA-TION BEHAVIOR OF HYSTERETIC LOOPS IN NONLINEAR STATIC ANALYSIS FOR SPECIAL MOMENT RESISTING FRAMES WITH SHEAR WALLS
سلمان رئیسی دهکردی
salman.raeisi@gmail.com
1
عبدالرضا سرو قدمقدم
sarvghad.moghadam@gmail.com
2
دانشگاه آزاد اسلامی واحد علوم و تحقیقات تهران
پژوهشگاه بینالمللی زلزلهشناسی و مهندسی زلزله
یکی از معایب آنالیز بار افزون آن است که اثرات کاهندگی را در رفتار غیرخطی سازه بهصورت تقریبی منظور میکند. برای بررسی این موضوع از ۶ قاب بتنی با دیوار برشی استفاده شده است، که مطابق با استاندارد ۲۸۰۰ و مبحث ششم مقررات ملی، بارگذاری و تحلیل و طراحی شدهاند. انجام تحلیلهای استاتیکی و دینامیکی غیرخطی نیز با نرمافزار OPENSEES انجام شده است. مدلسازی رفتار کاهندهی اعضای سازهیی با مدلهای رفتاری انجام و در مدلسازی، رفتار غیرکاهندهی آنها نیز ملحوظ شده است. تنشها و کرنشهای نظیر مقاطع با توجه به اثرهای محصورشدگی منظور \ شدهاند. نهایتاً \ مقادیر \ بیشینهی \ تغییرمکانهای \ بهدستآمده از \ تحلیل \ دینامیکی \ غیرخطی \ برای \ سطح \ خطر \ g ۰٫۳۵ با مقادیر نظیر حاصل از آنالیز بار افزون مقایسه شدهاند. نتایج حاکی از آن است که با افزایش ارتفاع، از اختلاف تغییرمکانهای با رفتار کاهنده و غیرکاهنده کاسته میشود، تا آنجا که میتوان از اثرات کاهندگی در محاسبهی تغییرمکان هدف، برای قابهای بلند صرفنظر کرد.
In this paper, the effect of the deterioration behavior of hysteretic loops in nonlinear static analyses (pushover) on special concrete moment-resisting frames with shear walls has been studied. One of the shortages in pushover analysis is that it approximately considers the effects of deterioration pertaining to hysteretic loops for structural elements. To evaluate this effect, it is necessary to perform nonlinear static and dynamic analyses and compare the results. To this end, six different planar frames, each one part of a three-dimensional design structure, have been modeled. All structures are the same in plane and different in height. After conducting the pushover analyses for defining the target displacement, dynamic analyses are also performed, considering the two different employed behavioral models. Because OPENSEES software has various behavioral characteristics for steel and concrete, and also has the ability to suitably model structural elements, it was used for performing the nonlinear static and dynamic analyses. In order to find the capacity curve of the structure, the displacement of the control node and the shear force of the base level were calculated using this software. For accurate calculation of the target displacement and bilinear idealization of the capacity curve, a computer program was developed in the Matlab environment to determine the target displacement, strength ratio (R) and etc. The employed material models are reinforcing steel material, concrete02 and hysteretic material. Deterioration behavior, as well as non-degrading behavior, is considered in nonlinear dynamic analyses. For modeling the structural elements, stresses and strains for each designed section are considered, with respect to confinement effects. The required backbone curve includes cracking point, yielding point and ultimate stress point, which are all derived from USC-RC software, and, of course, by considering element cross section, arrangement, number and size of reinforcing bars. Also, twelve ground motion records, which are scaled to 0.35g hazard level, have been used in time history analyses. Finally, maximum displacement amounts derived from inelastic dynamic analyses for 0.35g hazard level are compared with the amounts of target displacements, which express the maximum displacement of the structure under design earthquake, and we consider the effects of different parameters, such as deterioration, with the coefficient, c2. Results show that by increasing the height of the frame, the variance between frame displacement, with both deteriorating and non-degrading behavior, will be decreased, so that the effect of the deterioration behavior could be neglected in the target displacement calculation for high-rise frames.
https://sjce.journals.sharif.edu/article_830_78188b068cd2cd7160658c0dfa999ce9.pdf
رفتار کاهنده
تحلیل استاتیکی غیرخطی
تحلیل دینامیکی غیرخطی
قاب خمشی ویژه
دیوار برشی
Deterioration behavior
nonlinear static analysis
nonlinear dynamic analysis
special moment resisting frame
Shear wall
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
109
119
834
Research Note
رفتار لرزهیی میانقابهای آجری در قابهای بتن مسلح تحت اثر همزمان نیروهای داخل و خارج از صفحه
SEISMIC BEHAVIOR OF MASONRY INFILL WALLS IN RC FRAMES UNDER SIMULTANEOUS IN-PLANE AND OUT-F-PLANE LOADS
محسن علی نژاد
alinejad.157@gmail.com
1
مسعود سلطانی محمدی
msoltani@modares.ac.ir
2
عباسعلی تسنیمی
tasnimi@modares.ac.ir
3
دانشکده مهندسی عمران و محیط زیست، دانشگاه تربیت مدرس
دانشکده مهندسی عمران و محیط زیست، دانشگاه
تربیت مدرس
دانشکده مهندسی عمران و محیط زیست، دانشگاه تربیت مدرس
میانقابهای آجری به دلایل معماری و همچنین سازهیی به صورت گستردهیی در ساختمانها مورد استفاده قرار میگیرند. معمولاً میانقابهای بنایی عناصر معماری محسوب میشوند و وجودشان توسط مهندسان صرفنظر میشود. وجود میانقابها باعث ایجاد تغییرات عمدهیی در خواص سازه میشود، لذا درنظرنگرفتن نقش میانقابها در فرآیند تحلیل و طراحی، امری صحیح نیست. از میان مدلهای ارائهشده در این زمینه، مدل دستک فشاری به علت سادگی و دقت نسبتاً قابل قبول برای مدلسازی داخل صفحهی میانقابها، بیشتر از سایر مدلها مورد استفاده قرار میگیرد. طی رخداد یک زلزله، میانقاب بهطور همزمان در جهت داخل و خارج صفحه تحت اثر نیرو قرار میگیرد. این اثر همزمانی نیروها در بسیاری از مدلهای معرفیشده برای مدلسازی رفتار داخل صفحهی میانقابها از جمله مدل دستک فشاری نادیده گرفته میشود. از این رو در این نوشتار، به بررسی رفتار میانقاب تحت اثر همزمان نیروهای داخل و خارج از صفحه پرداخته شده است. بدین منظور ابتدا با ریز مدلسازی اجزاء میانقاب شامل واحدهای آجری و اجزاء تماسی، مدل یک طبقه و یک دهانهی قاب پرشده با میانقاب یا همان قاب مرکب مورد مطالعهی عددی قرار گرفته است. پس از مقایسهی نتایج تحلیل با نتایج آزمایشگاهی و اعتبارسنجی مدل، به بررسی اثرات همزمانی نیروهای داخل و خارج از صفحه بر رفتار میانقاب پرداخته شده است. نتایج پژوهش نشان میدهد که همزمانی نیروهای داخل و خارج از صفحه، اثر ناچیزی در ظرفیت داخل صفحه دارد، اما از ظرفیت خارج از صفحه میکاهد.
For structural and architectural reasons, masonry infill walls are widely used in building construction. Civil engineers usually consider infill walls as architectural elements and ignore them in structural analysis and design. However, it has been proven that infill walls change the behavior of structures, and, therefore, it would not be correct to ignore their significance in the analysis and design of a structure. The last few years have seen an increase in research into the subject, and many different models that consider the role of infill walls in analyses, have been proposed. Among all proposed models, the strut model is the most popular, thanks to its practicality and fair accuracy. During an earthquake, forces are applied both in-plane and out-of-plane of the infill wall. Nevertheless, this simultaneous effect is ignored in most proposed models (including the strut model). Thus, this research is an attempt to scrutinize the behavior of structures under such a simultaneous effect. In this research, first by micro modeling of the components of an infill wall, such as brick and interface elements, a one story, one bay model of an infill wall is made and subjected to numerical analysis. For this purpose, after comparing analytical results with experimental data and verification of the analytical model, the simultaneous effect of in-plane and out-of-plane loads is investigated. It shows that the in-plane damage has a significant effect on the out-of-plane stiffness and capacity of the infill wall. Furthermore, after careful studies on effective parameters in the behavior of the out-of-plane infill wall, it has been proven that the subject needs more in-depth study. The result of the research reveals that the simultaneous effect of the in-plane and out-of-plane forces has little to do with the in-plane capacity of the infill wall, but significantly reduces its stiffness and out-of-plane strength.
https://sjce.journals.sharif.edu/article_834_44f84bcc690d0ae041eba7ef847846be.pdf
میانقاب آجری
ریز مدلسازی
اثر همزمان نیروهای داخل و خارج از صفحه
مطالعهی عددی
Masonry infill wall
micro modeling
in plane-out of plane interaction
numerical analysis
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
121
127
835
Research Note
پیشنهاد مهاربند کابلی جدید برای مقاومسازی قابهای فولادی
\title{PROPOSING A NEW CABLE BRACING TO RETROFIT STEEL FRAMES
مهدی نجفی
m-najafi@iau-ahar.ac.ir
1
مجید برقیان
barghian@tabrizu.ac.ir
2
گروه مهندسی سازه، دانشگاه آزاد اسلامی واحد اهر
گروه مهندسی سازه، دانشگاه آزاد اسلامی واحد اهر
اضافهکردن مهاربند به قاب، سختی قاب را افزایش و نیز تغییرمکانهای جانبی در اثر نیروهای عرضی را کاهش داده، همچنین شکلپذیری را نسبت به قاب خمشی کاهش میدهد. در این پژوهش، نوعی مهاربند کابلی جدید پیشنهاد میشود. چندین قاب خمشی، قاب خمشی با بادبند کابلی X شکل و با بادبند پیشنهادی با هم مقایسه شدند و نتایج نشان دادند که رفتار قاب با مهاربند پیشنهادی، حالتی مابین قاب خمشی و قاب خمشی با بادبند کابلی X شکل است. با انتخاب قطرهای مختلف کابل و ابعاد متفاوت صفحهی مربعشکل بادبند پیشنهادی، نتایج را میتوان به نتایج قاب خمشی یا به بادبند کابلی X نزدیک کرد. در مهاربند X شکل، فقط یکی از کابلها به کشش کار میکند، اما در مهاربند پیشنهادی، همهی کابلها به کشش کار میکنند.
Bracing increases frame stiffness and reduces lateral displacement, due to transverse forces, but reduces frame ductility in comparison with moment resistant frames. A cable is known as a flexible element that can only undergo tension forces and has no compression strength. Using tension only elements within the bracing system of structures has created the idea of using cables as part of the lateral bracing system. In the present research, a new cable bracing is proposed. Different moment resistant frames with and without bracing, together with the proposed bracing, were analyzed and compared. Under the lateral load effect, the moment resistant frame shows the most displacement, compared to the same frame equipped with bracing. By adding the x-bracing cables to the moment resistant frame, displacements are reduced considerably, depending on the size of the cable diameter, due to additional stiffness by the cables. Adding a square plate in the intersection of the x-bracing cables (proposed bracing) show that the displacements are reduced compared with x-bracing cables, although the displacements were less than those obtained from the moment resistant frame. The results also showed that using x- bracing cables as a continuous form, gave more displacements compared to x- bracing cables used at each frame cell. By adding a square plate in the intersection of the x-bracing cables, the displacements are increased, while displacements are reduced by increasing cable diameter. In frames braced with cables, including the one proposed, increasing cable diameter causes an increase in cable axial load. Finally, the results show that the behavior of the proposed bracing is somehow between the behavior of the x-braced and the moment resistant frames. By choosing different cable diameter and a square shaped plate for the proposed bracing, the results tend towards either the x-bracing or the moment resistant frame. Only one of the two braces in the x-bracing cables acts under tension; while all cables are under tension in the proposed bracing.
https://sjce.journals.sharif.edu/article_835_43b60f40674232a300de35c09cfe81ea.pdf
مهاربند کابلی
قاب خمشی
کابل
تحلیل غیرخطی استاتیکی
مقاومسازی
Cable bracing
moment resistant frame
cable
non-linear static analysis
Retrofitting
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
129
136
827
Research Note
تأثیر پیشتصفیهی ازنزنی در فرایند فتوکاتالیستی چسبیده ـ معلق در تصفیهی فاضلاب رنگی و تعیین شرایط بهینهی آن
PHOTOCATALYTIC PROCESS IN DYE WASTEWATER TREATMENT AND DETERMINATION OF ITS OPTIMUM CONDITION
فرهاد قادری زفره ئی
f.qaderi@modares.ac.ir
1
بیتا آیتی
ayati_bi@modares.ac.ir
2
حسین گنجی دوست
h-ganji@modares.ac.ir
3
رسول صراف ماموری
rsarrafm@modares.ac.ir
4
گروه مهندسی محیطزیست، دانشگاه تربیت مدرس
گروه مهندسی محیطزیست، دانشگاه تربیت مدرس
گروه مهندسی محیطزیست، دانشگاه تربیت مدرس
گروه سرامیک، دانشگاه تربیت مدرس
در این پژوهش از ازنزنی برای حذف رنگ فاضلاب حاوی اسید اورانژ ۷ و از فرایند فتوکاتالیستی چسبیده ـ معلق نانو ذرات TiO$_2$ برای تصفیهی نهایی استفاده شده است. طبق نتایج حاصل، راندمان حذف COD با کاهش نرخ ازن تزریقی، افزایش غلظت اولیه، افزایش pH، کاهش تعداد آکنهها و کاهش توان منبع نوری کاهش یافت. سطوح بهینه، از روش طراحی آزمایش تاگوچی با تابع هدف کمینهی میزان انرژی مصرفی به ازاء حذف هر واحد COD برای متغیرهای غلظت اولیه )mg/L ۵۰(، pH )۳(، میزان ازن تزریقی )g/hr ۱٫۲(، غلظت نانوماده )mg/L ۱۲۸( و توان منبع نور )W ۱۲۰( بهدست آمد. در حالت بهینهی عملی، mg/L ۵۰ آلاینده در pH برابر با ۳ و با ازن تزریقی g/hr ۱٫۲ پس از ۱۳۵ دقیقه بیرنگ شد. در ادامه، با استفاده از ۳۰ آکنه )mg/L ۱۲۸ نانو مواد TiO$_2$( در معرض لامپ ۱۲۰ وات در مدت ۴ روز، ۸۹٪ از COD فاضلاب حذف شد.
Most \ dye substances are used in production processes and cause serious \ environmental \ pollution \ when \ discharged \ into the environment. Acid orange 7 is one of them, which has been studied in this research. Acid orange 7 containing wastewater is resistant to aerobic degradation and, under anaerobic conditions, can be reduced to potentially carcinogenic aromatic amines. Physical processes have difficulty in complete destruction of dye pollutants. Applications of both the slurry process and immobilized nano technology systems have recently been studied. Nano material agglomeration, light penetration in wastewater and the separation of nano materials from effluent are the most important disadvantages of the slurry process. The purpose of this study is to propose a new suitable treatment method. This method consists of pretreatment of dye wastewater with ozonation, undertaking the immobilized-suspended photocatalytic process as the final treatment. In the \ immobilized-suspended \ photocatalytic \ process, \ nano TiO2 \ were \ coated on submerged media. The coated media was characterized by Scanning Electron Microscopy (SEM) and Energy- Dispersive X-ray microanalysis (EDX) techniques. The result has shown that COD removal efficiency decreased with a decrease in ozone injection rate, an increase in initial concentration, an increase in pH,a decrease in the number of media (nano TiO2 concentration) and a decrease in power of the light source. An experimental design, based on the Taguchi method, was applied to assess the effects of several operating parameters, including dye concentration, TiO2 concentration, pH, light source power, and ozone injection rate, on the energy consumption of the treatment. Based on experimental design data, optimum conditions were achieved at 50 mg/L of initial dye concentration, pH of 3, ozone injection rate at 1.2 gram per hour, 128 mg/L of nano $TiO_2$ (media number equal to 30) and 120 Watt UV-A light source. Under these conditions, dye removal was completed after 135 minutes. Then, in the photocatalytic process, 89\% of COD was removed over 4 days using 30 media (128 mg/L), with 120 Watt light source.
https://sjce.journals.sharif.edu/article_827_9b0e384361e5aa82f6a419696952a1fd.pdf
ازن
TiO$_2$
فتوکاتالیست
اسید اورانژ ۷
تاگوچی
رنگبری
COD
Ozone
$TiO_2$
photocatalyst
acid orange 7
Taguchi
dye removal
COD
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2014-12-22
دوره 2-30
4.1
137
147
837
Research Note
تحلیل حدی مرز بالا با استفاده از روش بدون شبکه در خاکهای چسبنده
UPPER BOUND LIMIT ANALYSIS IN COHESIVE SOILS USING A MESH-FREE TECHNIQUE
سعید راعی
s.raei@sutech.ac.ir
1
سیدمحمد بینش
binesh@sutech.ac.ir
2
دانشکده مهندسی عمران و محیط زیست دانشگاه
صنعتی شیراز
دانشکده مهندسی عمران ومحیط زیست، دانشگاه صنعتی شیراز
در این نوشتار، با بهرهگیری از اصول کلی روشهای تحلیل حدی همراه با یک روش بدونشبکه، راهکاری جدید برای تعیین مرز بالای بار حدی در مسائل مکانیک خاک برای خاکهای چسبنده در شرایط کرنش صفحهیی ارائه شده است. بر این اساس، با درنظرگرفتن خاک بهعنوان یک مادهی صلب ـ کاملاً خمیری و تعریف نرخ اتلاف انرژی داخلی بر پایهی نرخ کرنشهای خمیری که شرایط تعامد را ارضاء میکنند و نیز با لحاظکردن قیود خاص برای بارهای خارجی، مسئلهی تعیین حد بالا به یک مسئلهی بهینهیابی ریاضی تبدیل شده است، که با استفاده از روش لاگرانژین حل شده است. در راستای محاسباتیساختن روش مذکور، لازم است که میدان سرعت در دامنهی مسئله مجزاسازی شود، که برای این منظور یک روش بدون شبکه مورد استفاده قرار گرفته است. استفاده از روش بدون شبکه این مزیت را دارد که بدون نیاز به تعریف المانها بهصورت مرسوم، میتوان محیط را مجزاسازی کرد و از پیچیدگیهای المانبندی برای ایجاد یک میدان سرعت سازگار کاست. در نهایت، با استفاده از روابط بهدستآمده، یک برنامهی رایانهیی تهیه و با حل چند مثال، کارآمدی و دقت روش نشان داده شده است.
A novel approach is developed for computing the upper bound limit load of soil mechanic problems in cohesive soils under plane strain condition. In this regard, the cohesive soil is considered as a rigid-plastic material which obeys the Von-Mises failure criterion. By implementation of the associated flow rule and the normality law, the stress at the yield state is related to the plastic strain increment. A mesh-free technique, called the radial point interpolation method, is adopted to express the strain increment field in terms of nodal velocities. Hence, both stress and plastic strain increment can be attributed to the nodal velocities, as well as the rate of internal energy dissipation. The discretized internal energy dissipation power, in conjunction with the incompressibility condition for the Von-Mises yield criterion and the conditions related to external loads, leads to a mathematical optimization problem which should be solved by an iterative technique. The technique consists of the establishment of the Lagrange functional and the formation of a linear system of equations by differentiation, with respect to the unknown nodal velocities and the Lagrange multipliers. By solution of the system of equations, the unknown nodal velocities and the Lagrange ultipliers can be found. The deficiency of the proposed technique is that there is no guarantee regarding the differentiability of the Lagrange functional at all points, due to the rigidity of some regions. Hence, an iterative ethod s sed o ndividuate the plastic and rigid regions in successive steps, thereby, solving the optimization problem. Indeed, the combination of a mesh-free technique with the limit analysis principles leads to a stable upper bound solution for the cohesive soil problem under plane strain condition, in which there is no need for mesh in the traditional sense. Based on the derived formulation, a computer code has been developed, and the accuracy and efficiency of the proposed method is demonstrated by solving some examples at the end of the paper.
https://sjce.journals.sharif.edu/article_837_9a80264ffcf5657f780c18dbc58dcdb4.pdf
روش بدون شبکه
خاک چسبنده
مرز بالای تحلیل حدی
Mesh-free method
cohesive soil
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2015-02-20
دوره 2-30
4.1
151
160
21006
چکیده مقالات به انگلیسی
ABSTRACTS OF PAPERS IN ENGLISH
-
-
https://sjce.journals.sharif.edu/article_21006_e3769fcbe37e289d741832b71c053f9e.pdf
-
-
per
دانشگاه صنعتی شریف
مجله ی مهندسی عمران شریف
2676-4768
2676-4776
2015-03-21
دوره 2-30
4.1
160
160
21005
شناسنامه و فهرست مقالات به انگلیسی
-
-
-
https://sjce.journals.sharif.edu/article_21005_7d2e36b5a8b5dbc8fc02f7d3b9c3fcd4.pdf
-
-